Welcome to our online store!

Log In / Register My Quote


Profile Information

Login Information

or login

First name is required!
Last name is required!
First name is not valid!
Last name is not valid!
This is not an email address!
Email address is required!
This email is already registered!
Password is required!
Enter a valid password!
Please enter 6 or more characters!
Please enter 16 or less characters!
Passwords are not same!
Terms and Conditions are required!
Email or Password is wrong!

Fuller Tool Box High Tack White Adhesive and Sealant 290ml

Code: 40-TBHTW
U.O.M. - Each
Toolbox High Tack is a one-part, high modulus hybrid adhesive with superior wet-grab strength. Ideally suited to bonding heavy objects such as metal signs to vertical surfaces. Toolbox High Tack also exhibits superior grab in overhead applications, making is especially suitable for bonding ceiling components.


Toolbox High tack is a one part, high modulus hybrid adhesive with superior wet-grab strength. It is ideally suited to bonding heavy objects to vertical surfaces. Toolbox High Tack also exhibits superior grab in overhead applications, making is especially suitable for bonding various ceiling components. It provides an efficient seal when compressed between substrates and is permanently flexible, skinning and curing rapidly. Toolbox High Tack skins in around 20 minutes and cures 3mm per day at 23°C.


  • Non-Hazardous; free of phthalate plasticizers
  • Cures to form a strong bond
  • Rapid skinning and curing
  • Non-corrosive – Does not attack substrates
  • High viscosity – Excellent green strength
  • Shock and impact resistant
  • No shrinkage
  • Very low odour
  • Permanently flexible in temperatures between -40°C and +100°C
  • Paintable wet on wet with waterbased paints
  • Resistant to water, dilute alkalis, cleaning agents, lime water and mould
  • Ideal for:

  • General assembly where a high level of bond strength and vibration resistance is required
  • Applications where a very high level of green bond strength is required
  • Installation of ceiling components, including soffit and other composite panels

    Surface Preparation:

    Toolbox High tack should be applied between 5°C and 35°C. Ensure that the substrates are clean and dry when Toolbox High tack is applied and do not apply where conditions may interfere with good bonding/sealing eg do not apply if frost or ice is present. Lightly contaminated surfaces should be wiped with Isopropyl Alcohol (IPA) using the 2-rag wipe method.


    Cut tip off cartridge. Screw nozzle on to cartridge. Apply to one surface to be bonded with the cartridge verical above the surface having the adhesive applied to it. Before product skins, mate with other surface.When bonding sheet or panel to a large flat surface, apply beads every 30-40cm along the entire length. Press into position and brace until set if required.

    Bond will develop dependent upon thickness of adhesive and ambient conditions. Higher humidity and warmer temperatures will hasten bond development. Minimum film thickness for bonding applications is approx. 2mm. Where a perimeter seal is required apply sufficient Toolbox High Tack relatively close to the edge of the substrate being bonded, so that the adhesive squeezes out to fill the gap between the mated materials. Tool off any excess with a spatula before Toolbox high tack skins.

    Clean Up:

    Clean up uncured adhesive with mineral spirits, IPA, Shellite or other suitable cleaner. Cured material can be removed by trimming with a knife or scraper.


    290ml cartridge will give approximately 8 linear meters coverage when applied using the supplied V notch nozzle.

    Additional Information

    10/4 - 4/10 Delivery Yes
    Colour White
    Suits Substrate Aluminium, Concrete, Fibre Cement, Fibreglass, Glass, Masonry, Plasterboard, Polyurethane / Plastics, Rubber, Steel, Timber
    U.O.M Each
    Box Quantity 12
    Brand HB Fuller
    Range / Model Tool Box
    Size 290 ml
    Min Working Temp -40 degrees Celsius
    Max Working Temp +100 degrees Celsius
    Gel Time / Skin Time Skins at 20 minutes at 23 degrees Celsius
    Cure Time 3mm per day at 23 degrees Celsius
    Modulus ca. 2.2MPa (Modulus of Elasticity DIN 53504 @100%)
    Shore A Hardness ca. 60
    Approvals & Certifications Non-hazardous according to GHS regulations
    Follow Us