Welcome to our online store!

Log In / Register My Quote
×

Registration

Profile Information

Login Information

or login

First name is required!
Last name is required!
First name is not valid!
Last name is not valid!
This is not an email address!
Email address is required!
This email is already registered!
Password is required!
Enter a valid password!
Please enter 6 or more characters!
Please enter 16 or less characters!
Passwords are not same!
Terms and Conditions are required!
Email or Password is wrong!

More Views

Fuller FulaFoam Pro Flexible Low Expansion Foam 750ml

Code: 40-FOPROF
U.O.M. - Each

More Views

FulaFoam PRO Gun Flexible Foam is easily compressed, regaining shape when pressure is removed. Fulafoam PRO Flexible gun applied foam is a low expansion PU foam that has been specially formulated to have highly efficient thermal and acoustic properties – up to 50% better than standard PU foams, due to an exclusive ‘micro-cell’ foam structure which results in improved sound and thermal insulation properties.

Details

Fulafoam Pro Gun Flexible Foam is designed to allow controlled filling and sealing of common construction materials. FulaFoam PRO Gun Flexible Foam is easily compressed, regaining shape when pressure is removed. Fulafoam PRO Flexible gun applied foam is a low expansion PU foam that has been specially formulated to have highly efficient thermal and acoustic properties – up to 50% better than standard PU foams, due to an exclusive ‘micro-cell’ foam structure which results in improved sound and thermal insulation properties of the cured foam.

Fulafoam PRO Flexible foam expands into free space, however the expansion is controlled and when applied as per directions, no warping or distortion of substrates and cavities will be observed. Foam will post expand up to 30%, variable dependant on temperature and humidity. It suits a range of substrates and is designed to be used with an applicator gun.

Features:

  • Fills cavities in a controlled manner
  • One part – no mixing
  • Compresses easily and regains shape when not under pressure
  • Paintable
  • Improved thermal and acoustic insulation
  • Ready to cut 30 minutes after curing
  • Suitable for:

  • Sealing around window and door frames
  • Sealing joints and penertration holes requiring flexible sealing against draughts, moisture and noise
  • Improving thermal and acoustic insulation
  • APPLICATION

    Surface Preparation:

    Ensure surfaces are clean, dry, sound and free of dust, oil old sealant or other contamination. For ideal results air and can temperature should be approximately 20°C. Protect all surfaces around the work area from contact with foam.

    Mixing:

    Shake can at least 20 times to mix contents. Screw upright can onto applicator gun and tighten (don't overtighten as this will make it difficult to remove). Pull trigger on gun while directing nozzle into the cavity to be filled.

    Placement:

    To inject the foam, turn the screw thread at the rear of the gun to open the valve, hold the gun vertically (the canister will be upside down over the gun) and direct nozzle into the cavity. Gently press trigger to release foam. The rate of extrusion can be varied, by turning the screw thread at the rear of the gun. To reduce chance of gun bonding to attachment ring in case of spillage, apply thin film of petroleum jelly or grease to metal ring before attaching gun.

    When filling large cavities, do no empty the whole can at once. Fill in stages, allowing the foam to expand between each stage. Using the whole can at once will cause failure of the foam in the middle of the mass to expand, resulting in reduced yield; or; too much foam may be injected. The pressure from the expanding foam may cause damage to the walls of the cavity.

    Inject the foam to cover a single layer. Depending on conditions, the foam should skin in 10-14 minutes. After it has skinned, spray a fine mist (not a puddle) of water onto the foam. Inject the next layer of foam.

    Clean Up:

    Surfaces surrounding the job area should be masked off prior to application. Clean up uncured foam immediately with acetone or Fulafoam Cleaner. When can has been emptied fully, gun should be cleaned with Fulafoam Cleaner internally and externally unless additional can will be used immediately. Foam should be cleaned from attachment ring before further can is applied as can may become permanently bonded otherwise. Cured material is very difficult to remove. Sanding or other mechanical means will remove most of the foam.

    Storage:

    Stores for 18 months unopened from date of manufacture. If open and correctly stored on gun, up to 4 weeks.

    Additional Information

    CODE 40-FOPROF
    10/4 - 4/10 Delivery Yes
    Colour Green
    Suits Substrate Aluminium, Brick, Cement, Ceramics, Concrete, Masonry, Plasterboard, Polystyrene, Timber
    U.O.M Each
    Box Quantity 12
    Brand HB Fuller
    Range / Model FulaFoam
    Gel Time / Skin Time Skins in 10-14 minutes at 23 degrees Celsius
    Cure Time 18 hours at 23 degrees Celsius
    Follow Us