Welcome to our online store!

Log In / Register My Quote
×

Registration

Profile Information

Login Information

or login

First name is required!
Last name is required!
First name is not valid!
Last name is not valid!
This is not an email address!
Email address is required!
This email is already registered!
Password is required!
Enter a valid password!
Please enter 6 or more characters!
Please enter 16 or less characters!
Passwords are not same!
Terms and Conditions are required!
Email or Password is wrong!

More Views

Fuller FulaFoam Pro Gun Applied Expanding Foam 750ml

Code: 40-FOPRO
U.O.M. - Each

More Views

Fulafoam Pro gun applied space filling foam is a multi-purpose, easy to use expanding foam that will fill cavities ranging in size from small gaps to larger spaces. Fulafoam Pro expanding foam can be used inside and outside and will adhere to a wide range of substrates. Designed for use with an applicator gun.

Details

Fulafoam Pro gun applied space filling foam is a multi-purpose, easy to use expanding foam that will fill cavities ranging in size from small gaps to larger spaces. Fulafoam Pro expanding foam can be used inside and outside and will adhere to a wide range of substrates. FulaFoam will not shrink when cured and will provide an airtight, moisture resistant seal.

Its curing time is highly variable and depends on weather conditions, ambient temperature and depth of joint, however 18 hours is the maximum cure time at 23 degrees Celsius; 24 hours at -5 degrees Celsius.

FulaFoam Pro skins in 10-14 minutes at 23 degrees Celsius and has a sound reduction index of 60dB.

Features:

  • Fills cavities without shrinking
  • One part – no mixing
  • Triple expanding
  • Paintable
  • Insulating
  • Suitable for:

  • Sealing around penetrations through walls and floors
  • Sealing gaps between polystyrene panels
  • Filling holes in walls
  • APPLICATION

    Surface Preparation:

    All surfaces must be clean, sound and free from dust, grease, oil and contamination. High humidity and dampness will aid the expansion of the foam, however, the surfaces should not be wet. Spraying a fine mist of water into the cavity will aid expansion of the foam.

    Mixing:

    Ensure that the temperature is greater than 5°C. Shake can at least 20 times before each use to ensure that contents are mixed. Attach the canister of foam to the gun by aligning the thread on the canister and gun and turn until locked in position. The canister may have to be gently pushed into the screw thread to ensure engagement of the mechanism.

    Placement:

    To inject the foam, turn the screw thread at the rear of the gun to open the valve, hold the gun vertically (the canister will be upside down over the gun) and direct nozzle into the cavity. Gently press trigger to release foam. The rate of extrusion can be varied, by turning the screw thread at the rear of the gun. To reduce chance of gun bonding to attachment ring in case of spillage, apply thin film of petroleum jelly or grease to metal ring before attaching gun.

    When job is complete fully close valve and keep can on the gun unless empty. If empty can may be removed, however gun must be cleaned if stored or not used immediately.

    When filling large cavities, do no empty the whole can at once. Fill in stages, allowing the foam to expand between each stage. Using the whole can at once will cause failure of the foam in the middle of the mass to expand, resulting in reduced yield; or; too much foam may be injected. The pressure from the expanding foam may cause damage to the walls of the cavity. Inject the foam to cover a single layer.

    Depending on conditions, the foam should skin in about 10 minutes. After it has skinned, spray a fine mist (not a puddle) of water onto the foam. Inject the next layer of foam. Repeat until the cavity is 1/3 to 1/2 filled. Fulafoam Pro expanding foam will expand to approximately three to four times the extruded volume.

    Trim cured foam using a saw, knife, rasp or sand paper. Paint with an exterior grade acrylic.

    Clean Up:

    Surfaces surrounding the job area should be masked off prior to application. Clean up uncured foam immediately with acetone or MaxPro cleaner. When can has been empties fully, gum may should be cleaned with Maxpro cleaner internally and externally unless additional can will be used immediately. Foam should be cleaned from attachment ring before further can is applied as can may become permanently bonded otherwise. Cured material is very difficult to remove. Sanding or other mechanical means will remove most of the foam.

    Storage:

    Stores for twelve months unopened from date of manufacture. If open and correctly stored on gun, up to 4 weeks.

    Yield:

    When used strictly according to directions and depending on humidity and temperature, 750ml can of Fulafoam Pro will yield approximately 45 litres of foam.

    Additional Information

    CODE 40-FOPRO
    10/4 - 4/10 Delivery Yes
    Colour Yellow
    Suits Substrate Aluminium, Brick, Cement, Concrete, Fibreglass, Galvanised Iron, Particleboard, Plasterboard, Plywood, Steel, Timber
    U.O.M Each
    Box Quantity 12
    Brand HB Fuller
    Range / Model FulaFoam
    Size 750 ml
    Gel Time / Skin Time Skins in 10-14 minutes at 23 degrees Celsius
    Cure Time 18 hours at 23 degrees Celsius
    Follow Us