Welcome to our online store!

Log In / Register My Quote
×

Registration

Profile Information

Login Information

or login

First name is required!
Last name is required!
First name is not valid!
Last name is not valid!
This is not an email address!
Email address is required!
This email is already registered!
Password is required!
Enter a valid password!
Please enter 6 or more characters!
Please enter 16 or less characters!
Passwords are not same!
Terms and Conditions are required!
Email or Password is wrong!

Fosroc Cemtop XD Floor Topping 15 kg

Code: 40-FC602055-15KG
U.O.M. - Each
Cemtop XD cement based floor surfacing system consists of a blend of selected cements and hard wearing aggregates modified with polymers and flow agents. It is designed to be used in conjunction with Nitoprime 330 Primer. It creates an internal trafficable wearing surface from 6 to 12 mm thickness.

Details

Designed as an internal thin layer industrial wearing course for use in areas that are subjected to both foot and forklift traffic. Can be used for the reinstatement of existing floors or as a final wearing course on new concrete floors where specified floor tolerances have not been achieved or where, for speed of installation, the concrete floor has been left with a rough screed finish. Suitable for use across a wide range of industrial environments such as warehouses, light to medium engineering operations, food processing plants, car parks etc. May be used either as a stand-alone system or, depending upon end use of floor, in conjunction with Nitoflor or Durafloor floor coatings.

Features:

  • Very fast application and rapid cure - minimises factory downtime
  • Economic - more cost effective than equivalent resin based systems
  • Dimensionally stable - can be installed in large jointless areas
  • Self smoothing - minimal finishing required
  • Durable - smooth dense surface, resistant to forklift truck traffic
  • One pack product, applied by pump - eliminates on-site batching and ensures consistency of mixed product
  • Ideal for:

  • Reinstatement of existing floors
  • As a final wearing course on new concrete floors where specified floor tolerances have not been achieved
  • Concrete floors that have been left with a rough screed finish
  • Wide range of industrial environments such as warehouses, light to medium engineering operations, food processing plants, car parks etc.
  • Use stand-alone or in conjunction with the Nitoflor range of resin based floor coatings
  • APPLICATION

    Surface Preparation:

    The installation of Cemtop XD is a specialised activity. The product should be applied by an experienced contractor who has been fully trained in the use of the product and equipment. Although the preferred method of application is by the use of a continuous mixer pump, it may, in certain circumstances, particularly for floor areas less than 50 metres square, be more practical to mix and apply the product by hand. Refer to the Technical Data Sheet for further information.

    Mixing:

    When mixing Cemtop XD by hand use 2.55 litres - 2.85 litres (Av. 2.70 litres) of cool clean drinking water per 15 kg bag.

    Placement:

    Pour the mixed material on to the dry primed surface, spread with a trowel and allow to self-smooth. Roll surface with the purpose made spiked roller. Best results are achieved when the pouring and levelling is a continuous process. Note: If the mix stiffens it should be discarded, do not attempt to re-mix with water. In areas that are subject to continuous water exposure or chemical attack from acids or organic solvents, Cemtop XD should be protected using one of the Nitoflor range of resin floor coatings. Refer to the Technical Data Sheet for further information.

    Clean Up:

    Remove from tools and equipment with clean water immediately after use. Hardened material can only be removed mechanically.

    Storage:

    Shelf life of 12 months when stored in a cool dry area.

    Yield:

    Each 15 kg bag yields approx. 8.85 litres when mixed with 2.70 litres of water. 8.85 litres will cover approximately 1.5 square metres at 6 mm thick.

    Additional Information

    CODE 40-FC602055-15KG
    10/4 - 4/10 Delivery Yes
    U.O.M Each
    Brand Fosroc
    Size 15 kg
    Appearance / Composition Powder
    Application Thickness (mm) 6 - 12 mm
    Cure Time Accepts foot traffic in 2 - 4 hours, and light traffic from 24 hours
    Compressive Strength at 28 days (MPa) >27
    Yield Approximately 8.85 L when mixed with 2.7 L of water. This will cover 1.5 square metres at 6 mm thick
    Follow Us