Welcome to our online store!

Log In / Register My Quote


Profile Information

Login Information

or login

First name is required!
Last name is required!
First name is not valid!
Last name is not valid!
This is not an email address!
Email address is required!
This email is already registered!
Password is required!
Enter a valid password!
Please enter 6 or more characters!
Please enter 16 or less characters!
Passwords are not same!
Terms and Conditions are required!
Email or Password is wrong!

FortiAnchor FA-E400 Epoxy Anchor 400ml

Code: 40-FAE400
U.O.M. - Each
FortiAnchor Epoxy is a two-component non-sag, high performance, solvent-free, epoxy anchoring adhesive. It is ideal for anchoring rebar, threaded rod and fasteners into concrete and other substrates, including hard stone, solid rock and masonry products. FA-E400 Epoxy Anchor is available in a 400ml dual cartridge.


FortiAnchor FA-E400 Pure Injection Epoxy is a two component non-sag, high performance, solvent-free, epoxy anchoring adhesive. FortiAnchor FA-E400 is ideal for anchoring rebar, threaded rod and fasteners into concrete and other substrates, including hard stone, solid rock and masonry products. It fixes well to concrete, hard natural and reconstituted stone, solid rock, hollow and solid masonry, steel and wood.

FortiAnchor FA-E400 is suitable for dry or wet but not flooded holes. It achieves a gel time of 4 minutes at 40 degrees Celsius, allowing loading in 3 hours. At 10 degrees Celsis, FA-E400 gels in 60 minutes and can be loaded in 12 hours.


  • ETA Approved for Post installed rebar connections diameter 12mm to 40 mm
  • For use in vertical down and horizontal installations
  • Fast curing time
  • Low odour, styrene free
  • Ability to be used in wet/damp areas
  • High load capacity
  • Non-sag, even overhead
  • Can be used on non cracked concrete
  • Highly stable, offers high performance
  • Ideal for:

  • Rebar / steel reinforcement anchoring in new and refurbishment works
  • Threaded rods
  • Bolts and special fastening systems
  • Anchoring supports for ducting and equipment
  • Fixing handrails, balustrades, supports, railings, window frames and door frames

    Surface Preparation:

    Ensure holes are blown clean and free of debris. Material must be at a temperature of between +10°C and +40°C for application.


    Prior to dispensing into the anchor hole, squeeze out separately the mortar until it shows a consistent pink / grey colour, and discard non-uniformly mixed adhesive components. Apply the 3:1 mixture to a maximum embedment depth of 800mm, in a maximum 5mm layer.


    Bore hole filling - Start from the bottom or back of the cleaned anchor hole fill the hole up to approximately two-thirds with adhesive. Slowly withdraw the static mixing nozzle as the hole fills to avoid creating air pockets.

    Rebar/anchor inserting - Insert the anchor with a rotary motion into the filled drill hole. Some adhesive must come out of the hole. Important: the anchor must be placed within the open time. During the resin hardening time the anchor must not be moved or loaded.


    24 months from date of production if stored properly in original unopened packaging in cool and dry conditions.

    Further technical information available on request.

    Additional Information

    CODE 40-FAE400
    4 Hour Delivery Yes
    Colour Pink
    Suits Substrate Concrete, Masonry, Rock, Steel, Stone, Timber
    Similar Products Powers Pure 150-Pro
    Ramset Chem-set 101
    U.O.M Each
    Box Quantity 20
    Brand FortiAnchor
    Size 400 ml
    Appearance / Composition Multi-Part Mixture
    Gel Time / Skin Time 20 minutes (Tested to ASTM D2471-99)
    Compressive Strength at 28 days (MPa) 84 (typical)
    Approvals & Certifications ETA Approved for post installed on rebar connections 12mm - 40mm
    Follow Us